|MKS HV6100 Specifications|
|Body dimensions||22.6 mm wide x 10.0 mm thick x 24.0 mm high||0.89" wide x 0.39" thick x 0.94" high|
|Max dimensions||31.0 mm wide x 10.0 mm thick x 25.0 mm high||1.22" wide x 0.39" thick x 0.98" high|
|Stall torque (6V)||2.60 kg.cm||36 oz.in|
|Stall torque (7.4V)||3.00 kg.cm||42 oz.in|
|Stall torque (8.2V)||3.40 kg.cm||47 oz.in|
|Weight||10.0 g||0.35 oz|
|Lead length||18 cm||7.1 in|
|Operating speed (6V)||0.14 sec/60°|
|Operating speed (7.4V)||0.11 sec/60°|
|Operating speed (8.2V)||0.10 sec/60°|
|Operating voltage||3.8V to 8.4V|
|Bearings||2 jewel bearings + 1 bronze bush|
|Gear material||Aluminium-magnesium alloy|
|Motor type||Coreless DC motor|
|Working frequency||333 Hz|
|Dead band||1 µs|
|Supplied accessories||2 plastic output arms, 2 arm retaining screws, 2 mounting screws|
|Optional accessories||Frame for MKS DS6100, Frame with bearing for the MKS DS6100, Integrated Drive System/Mono for MKS DS6100, MKS Plastic Servo Output Arms, MKS Heavy Duty Plastic, MKS Short Metal Servo Output, MKS Long Metal Servo Output Arms, MKS RDS adaptor, Replacement Gear Set for MKS HV6100|
Review by: Eamon KeatingF5J
Purchased four of these for my Xplorer F5J, for the ailerons, rudder and elevator and they have performed beyond expectations. Only issue is noise :-) These are noisy servos, probably the noisiest I have ever heard, but they centre perfectly and are an excellent choice for high performance gilders.
I would highly recommend these.
Review by: stevenTop servo
Very nice, slop free, powerful servo!
Review by: Brucehigh quality, worth it
I've been a 6100 fan for a yr now, (tried the KST substitute first for a while, not happy). These are light, tough, and nicely all boxed in (i'm not a fan of micro servos that have wires exposed). Only minor complaint is that for me, the HV version of the 6100 gives off ,periodically, a static noise, never experienced that with the standard 6100, I'm using these with a LiFe battery for the receiver.
Review by: Jereon Kole
Very robuust and powerfull servo.
Use it on flaps for f5j
Review by: Stevengood servo's
Very nice and precise servo's
Quicker than the non hv ds6100 servo's
No slop at all! Very happy!
Review by: Bullmann, Franz
The service was excellent and the shipping quite fast. The only negative item was, that your e- mails were nearly unreadable.
Best regards- Franz Bullmann
Review by: AnonymousMKS HV6100 & Vladimir's Supra Expert LDS mount set
This combination should fit into just about any tight F3X fuselage. It's an overkill for what I'm doing, converting an old F3J model to F5J for a practice hack, however the LDS mount set is the only way I can see to make it happen in the fuselage space available.
Review by: SiMKS HV6100 Servo - 10mm 10g 3.4Kg.cm
Bought to replace a faulty unit, but a nice, quick, strong servo.
Review by: Peter Wood
Excellent little servo. Fast, powerful and accurate. Only slight criticism is that the raised casing behind the output arm interferes with the pushrods when trying to install two diagonally in a narrow F5J fuz. I had to install them in tandem with some complicated mounting arrangements.
Review by: DG
These really are a great little servo - tuck in virtually anywhere.
and if your running a Rx that can handle higher volt supply and you are running these with long cables there just the job
Review by: AnonymousMKS HV6100
Even faster than the normal DS6100, very precise, zero slop. My choice for F3X gliders with narrow fuse, on v-tail where absolute precision is needed for minimal throw and trim adjustments!