Prices shown exclude VAT 

Ripmax SD100 Servo - 8.1mm 4.7g 1.1Kg.cm

Product Code: SD100
 (35 reviews)

Price: $24.43

More than 30 in stock
Quantity

Description

The Ripmax SD100 is exactly the same servo as the Dymond D47, and is rated for up to 8.4V operation. This allows it to be used with a 2S LiPo receiver battery without a voltage regulator, reducing cost and increasing reliability - and allowing useful rx battery voltage info to be transmitted back to the pilot when using modern telemetry radios.

The Ripmax SD100, like the D47 is a precision 4.7 g analogue servo with a good torque and excellent centring. It has a low backlash geartrain and can be used for all control surfaces. Suitable for models weighing up to 1 Kg.

Another benefit of the SD100 (and D47) is the very low operating current. This increases the flight time of the model by about 40% in comparison to a similar digital servo.

Ripmax SD100 Specifications
Body dimensions 21.9 mm wide x 8.1 mm thick x 17.7 mm high 0.86" wide x 0.32" thick x 0.70" high
Max dimensions 29.7 mm wide x 8.1 mm thick x 22.0 mm high 1.17" wide x 0.32" thick x 0.87" high
Stall torque (4.8V) 1.10 kg.cm 15 oz.in
Stall torque (6V) 1.40 kg.cm 19 oz.in
Weight 4.7 g 0.17 oz
Lead length 12.5 cm 5.0 in
Operating speed (4.8V) 0.18 sec/60°
Operating speed (6V) 0.14 sec/60°
Operating voltage 4.0V to 8.4V
Bearings Plain bearing
Gear material Plastic
Motor type Brushed
Digital No
Programmable No
Supplied accessories 4 plastic output arms, 2 arm retaining screws, 2 mounting screws, 2 plasic side mounting tabs
Optional accessories Frame for SD100/D47

Reviews 35  


 Review by:

Ripmax

surprisingly this servo was defective out of the box.


 Review by:

Nice little servo, use it in the Fling DLG. Would be nice when it had a bit a longer lead.
Works fine


 Review by:

Brilliant little servos, one of my favorites. Zero issues with them, plenty fast enough on 1s too.


 Review by:

Ripmax SD100 servo

Bought these for my Dreamflight Libelle DLG as aileron servos. I chose them because previous reviewers had said how robust they were. Unfortunately one of them has stripped gears after a relatively minor nose down landing and I have to replace the gears. A bit disappointing but other than that they work really well.


 Review by:

Great servos! Using them in a FW 6.2 and in a ELF DLG for the elevator and the rudder. Thanks Neil for the great shipping service to Switerland!


 Review by:

Reliable tiny lightweight

I have used several of the SD100 (also a couple of 150s) servos from Neil and found them great. They seem very reliable, centre well, are slop free and are ideal in lightweight models. Two points in their favour are that they can be fitted in a glider tail without the need for church roof to get CofG right and they will operate off 2S LiPos.


 Review by:

Nice small servo , good quality, work very well


 Review by:

The Greatest analog micro servo

Precise servo capable to handle fully charged 2s Li-Po cell.
Those from batch I received, were totally jitter free, holding 0 position precisely.


 Review by:

like the diamond servos - reliable servo for the ruder and elevator


 Review by:

Buono

Ottimo servo e ottimo sito


 Review by:

Servo delivers everything promised in specs. I see why they are recommended for the Elf Mini DLG.


Comment by:

Un clásico para DLGs y veleros pequeños. Siempre se ha portado estupendamente.
El servicio de Hyperflight, como siempre, excelente.


 Review by:

All good

Great servo


 Review by:

Your service is faultless thank you. The servos themselves are as usual up to there good quality and performance.


 Review by:

Nice servo, quite powerful for its size. the only
reason it didn't get 5 stars is because the the lead is too short.


 Review by:

Great Little servo, great service as well

I am converting some old free flight models to basic R/C and needed some small reliable servos. I bought two from a well known bulk cheap HK based internet site, one of which failed on first use. A friend into HLG recommended this servo and it is just in a different class. The service from Hyperflight was very good. The servo may well have been three times the price of the one that failed but so far worth every penny


Comment by:

bonjour suit a un servo ripmax sd100 qui a griller j ai recommandé 2 autres servo .tres content du produit meme si il y a des servo defaillent .
serait il possible d etre livrer plus vite !
merci hyperflight


 Review by:

Ripmax SD100 Servo

Great little servo. I have used two of these as elevator servo's for two pylon racers I own. Would highly recommend and would certainly buy them again.

10 out of 10.


 Review by:

Excellent servo.

I have these in the Elf. They have been used a lot and are holding up excellent. Noe slope in the gears. Will buy again. Excellent servo.


 Review by:

Tiny and solid

I just bought my second set of these servos, for a new plane. The first sett have been working flawlessly for two years in my frequently used Elf DLG. I am running two servos and an Orange dx 4 channel rx directly of a 1s300 lipo without any problems.
All 6 servos I have recieved have been stable and well centering on the servo tester and in the field.
Thay are expensive, but worth it!


 Review by:

Solid preformers

I have had two of these in two Elf fuselages over two years. They have suffered plenty of cartwheels and hangar scruffing with out the slightest problem. I am now buying four more for a Lbelle
They are worth it


Comment by:

Incompetent builder?

Quality of kit is excellent but instructions not adequate ( at least for me)
The fuselage is on the bench partly completed but likely to remain that way for some time.
I mistakenly believed the fin and elevator would align correctly when assembled as the elevator mount is pre-installed and the fin slot pre-cut. Not so and I now have a fin cyanoed in place and not at 90 degrees to the elevator. On the instructions downloaded (too late) from the maker's website it emphasises that care must be taken to ensure the fin is set at right angles before glueing but not on the instructions with the kit.
I also have the fin push rod cyanoed in place to the horn using a piece of wire insulation tube and it needs to be removed to assemble the servo connection. Similar problem with the elevator push-rod. Again, the downloaded instructions are more detailed and helpful.
Maybe I should have known better but I am not an inexperienced model builder - albeit most of my experience dates from the 20th century and is,perhaps, not relevant when using 21st century materials and methods.
Hopefully, I'll sort the problems eventually.


 Review by:

Ripmax SD100 Servos

I was having trouble fitting servos in the ELF DLG.
The Ripmax SD100 Servo's do fit OK.


 Review by:

Have used these servos for years and have nothing but respect for them. Perfect for rudder and elevator on 1.5m DLG's. I will be coming back for more…..


 Review by:

2 duff servos out of 4 which, both could of led to radio failure. Disappointing for the money. Hopefully this will be rectified by Hyperflight who have changed one without question. Thank you.

HyperFlight comment:
Multiple failures in one plane suggests an installation error, as our overall returns rate for this servo is about 2%. However we have credited Ray.


 Review by:

Great little servos easy to fit

Fast speedy delivery and help from Neil on the phone much appreciated.
Gerry


 Review by:

Great little servo

Amazing little (tiny) servo. Great performance from such a small servo. Fast delivery from Hyperflight too. Thank you.


 Review by:

Got two of these for my Elf. Not had any trouble with them...easy to fit, set up and fly with. Would buy them again.


Comment by:

excellent service

These servos are really small and light, not cheap, but good quality.
BOB.


 Review by:

Power!!

Expensive but worth it. They centre superbly, run off a 2 cell lipo and have loads of fittings. Use in an Elf DLG and brilliant. Very happy with them and worth the price. Don't bother looking around they are this price everywhere. As they say, you get what you pay for.


 Review by:

Low profile wing servo

These SD100 servo are superbly engineered and remarkably efficient. I use 4 in my Blaster 2e but in hindsight would have started out with the more robust SD150 for wing flaperon use, with the SD100 for rudder and elevator. A heavylanding under gusty conditions or even careless handling of the wing control surfaces can strip the nylon gears.

Comendation to Hyperflight for super quick response on two replacements and it would be great if spare gear sets could be stocked in due course. A shame to bin such a good servo for the lose of a couple of teeth.


 Review by:

Just the jobbi

Does sterling work on my Elf, highly recommend.


Comment by:

Great little servo up to the job but handle with care


 Review by:

Great little servo

Using these micro servos inall sorts of applications. Never had a bad one.
Stripped a gear due to turning servo arm (dont do it) but spares easily available so fixed in no time. Surprising power and very fast especially on 2 cell lipo with MPX or Jeti Rx that can also run on 9volts.


 Review by:

Quality Micro Servo

Using these micro servos in lots of models - Gliders and Egliders, indoor 3D, Tomboy/Mills 2Channel and small EDF.

Never had a bad one. Stripped a gear once due moving servo arm (never a good idea) but just replaced gearset.

Well worth the money................ IMHO


Related Products 0

Shop Securely

Follow Us

facebook   twitter   Google+

Contact Us

HyperFlight
Drybank Farm
Fosse Way, Ettington
Stratford-upon-Avon
Warwickshire, CV37 7PD
United Kingdom
+44 (0) 1789 336166
sales@hyperflight.co.uk
Contact Form