|Blaster 2e Specification|
|Wing span||1.49 m||58.6 in|
|Wing area||22.9 dm2||354 sq in|
|Flying weight from||360 g||12.9 oz|
|Wing loading||15 g/dm2||5.0 oz/sq ft|
|Wing airfoil||AG45, AG46, AG47|
|Centre of Gravity||74-84 mm from wing leading edge|
|Controls||Elevator, flaperons, throttle, rudder|
|Spinner size||32 mm|
|Canopy hatch size||100 mm x 28 mm (4" x 1.1") with curved ends and sides|
|Max battery size||9 5mm x 35 mm x 25 mm (3.75" x 1.4" x 1")|
|Blaster 2e Typical Weights|
|Fuselage||50 g||1.8 oz|
|Wing||149 g||5.3 oz|
|Hoz tail||10 g||0.35 oz|
|Vert tail||7 g||0.25 oz|
|Total structure||231g||8.1 oz|
|Aileron servos||Ripmax SD100, Ripmax SD150, Blue Bird BMS-101HV, KST X08, Corona DS843MG, Hyperion DS09-SCD|
|Rudder & elevator servos||Ripmax SD100, Blue Bird BMS-101HV|
|Receiver||5 channel rx to match your transmitter|
|Recommended Control Throws & Mixes|
|Rudder||25mm each way|
|Tailplane||10mm up / 10mm down|
|Flaperons||15mm up / 8mm down|
|Recommended flaperon settings>|
|Speed mode||-2° (flat bottom surface)|
|Cruise mode||0° (flat top surface)|
|Thermal mode||+2° (2mm down)|
|Landing mode||+40° (38mm down)|
Review by: Mark buddBlaster 2e sc
I must say the finish is amazing as good as my snipe 2 with I got from hyperflight now just need to sort out the install witch is going to be a light install witch Neil said he will help me with thanks hyperflight for all your help 😀👍
Review by: Richard Clark
It's great to see the beautiful E Blasters back in stock with Hyperflight!
My new E-Blaster arrived swiftly and soundly packed. Two previous Blasters have proved superb fliers, easily repaired, and ideal for flight in wind range 0-15mph.. It is unsuitable for novice fliers, and requires good constructional skills.
I fly in a windy turbulant site, I fly with an E Max BL2210/30, 11x9 prop, and 3S 1000mAh battery. With this, the Blaster will streak up to the cloud base in 20-30 seconds, leaving you to thermal idefinitely even on dull days that initially apear unpromising.
Two points to consider:
1. The vertical stabilizer is tricky to assemble. Use the left over wing servo carbon fibre cutout to make an access hatch for the two SD100 servos in the fin. This is better for simplicity, soundness, and accuracy of installation. The clearence of the lower servo arm with the boom is very tight and I have found it best to open up a small slot in the boom to allow for this. To maintain and improve the structural strength of this well known weak area, fit a length of 6mm carbon tube, inside and along the bottom of the boom. 80mm length will reinforce from just ahead of the fin front 'O' ring out to 30mm out beyond boom end and provide a short skeg to protect the rudder. As with all assembly use Rapid Set Epoxy which is reworkable.
2. Control linkage construction with carbon tube and 0.8mm wire ends is great for getting precise control lengths. Failiures can occur, so replace these with one piece wire linkages. Anti-flexing carbon tube will only be needed on the long elevator link.
Review by: john knowlesBlaster 2e
After lots of researching, it was pretty clear that the guys at Hyperflight were the people to speak to.....
...which I did! In particular, Paul was incredibly helpful, going well beyond the extra mile. What a great glider - there's plenty of advice within the instructions and numerous stuff online. Not an ARTF model, the main components are manufactured to a very high standard, it will require some careful consideration and application. My advice is to take time to speak to Hyperflight - they will advise on all the additional hardware.
The Blaster is a great performer - get it close to weight/cg/control throws - and fine tune it from there to ensure maximum fun!
I strongly recommend listening to these guys - they walk the walk!
Review by: DavidPink is great for visibility
I've had my Blaster for a couple of years and thought I had reviewed it! Obviously not so here goes. This model is gorgeous even in pink. It flies superbly and climbs so well on the cheap motor set up although a 3S 450 performs far better than the 2S i started out with. It handles beautifully and will all too easily hook thermals and become a dot needing determined full spoilerons and dive to escape ~ pink's a good visible colour! I don't disassemble it as it goes in the boot relatively easily hence it's the model of choice in less windy conditions. Build quality is excellent and hinging is neat.
Review by: ThomasBlaster 2e
SD150 aileron servos
SD100 tail servos
FVT 20A ESC
9x5" gemfan folding prop with vladmir's hyperspinner
2S 1300mAh 35C
This was my first glider kit, and I took my time to build it. I used a motor/ESC combo from another build, with the 9x5 prop it pulls about 18A. Not the most efficient, but it has a ton of power and easy vertical.
I followed the excellent manual regarding CG & deflections, and it flew perfectly on its maiden. At 415g AUW, the CG was perfect with a 1300 2S lipo. Total powertrain weight with prop & firewall was just under 60g.
HyperFlight's service was top notch, and ploof's RCGroups build log was very helpful, especially the discussion with Neil and other forum members.
Here is my maiden flight, a bit gusty and I only had to use the motor near the end : https://www.youtube.com/watch?v=a9fgvdWnw_U
Review by: RichardBlaster e
After much deliberation I bought a blaster e. The quality of the model is higher than anything I have seen before and the delivery from hyperflight excellent.
I went against the advice of Neil and tried to use an sd100 for the elevator and a cheaper alternative for the rudder. Beware alternatives do not fit.
The build was ok, the only problem being that one of the Dsm44 servo was faulty and was only obvious once installed. To Hyperflight's credit they sent a replacement the following day. With an incredibly low built weight the performance of the Blaster is sublime in light winds. I have yet to try it in something stronger. Unfortunately I flew it into a goalpost on my local field resulting in some damage to the wing. Although sadly it is no longer as pretty as it was it still flies very well after a repair. Definitely recommended.
Review by: Richard
Delivered successfully and on time. Many thanks.
If it goes together and flies as well as it looks it should be superb.
Could I also please give feedback on the delivery service which was exemplary. Not only was it on time but it gave excellent information on when it would be delivered. Top class all round.
Just one complaint though I an afraid. There are too many tantalising products on your website which is not really good for my bank account.
Review by: Ant. ClarkBlaster 2E
Blaster and motor received in good order; very prompt delivery and excellent packing.
Have not been able to assemble and fly my Blaster yet.and am away in France for rest of month so will get a review done in due course.
However I have flown my brother's model.....
Superb machine, a pure delight to fly,excellent slope flying and wonderful to watch it just wafting along "hands off"
Review by: J.H.Foster.assessment of kit parts & layout
As an ex competition F/F builder/flyer, I was impressed with the build standard of the 'Blaster 2e'....the wings are fabulous. I have just started installation of the CF2822.
The model will include a lot of my personal mods to refine the build. I found the the various builder/flyers websites quite informative.
Comment by: d gay.blaster 2e
Very taken with the superb quality of this model.
Once again you get what you pay for, cannot be improved in any way.
10 out of 10
Review by: RichardBlaster 2e - useful advice on assembly
Dream Machine! High pressure, stable air, no thermals but a gentle flow of air up a large south facing stubble field with a ten foot hedge row at the top. My Blaster 2e tracked to and fro along the stationary wave created by the hedge, no power input required, just lowered the flaperons about 5 deg and immensely satisfying flying! A wonderfully aerodynamic machine.
My setup: EMAX 2822, 15A ESC, 10x6 prop, 4xSD100 servos, Futaba R617 2.4GHz Rx.
For light air 500mA 3s LiPo, giving 6 climbs of 30s. Flying weight for thermalling is 394g AUW.
For 15-20mph winds 850mAh LiPo, with AUW 415g; plenty of fast flying with good penetration to windward. No additional balancing weight needed.
Two noteworthy points concerning assembly:-
1) To get a really good alignment of the motor and spinner: ensure motor is mounted geometrically central on the supplied bulkhead, cut three air flow slots on the circumference, mount using 3mm bolts. Now face the smaller front mounting bulkhead with a thin ply disc. Drill a 3mm hole absolutely centerally and glue bulhead temporarily. You can now slide motor and bulkhead forward so that the shaft engages the 3mm hole and is thus in true axial alignment ready for epoxying into correct position.
2) A neat way of connecting wing servos to the Rx in the fuselage. Cut the female servo connectors from the wing servos. Now wire up the two futaba female connectors into a four wire harness(Common. +ve supply, signal left aileron, and signal right). Terminate this in a 4pin JST-XH socket (ie a balancer socket from Lipo). Feed the the females down through the wing pylon to the Rx Ch1 and Ch6. The second part of the harness starts with a four pin plug but you need to solder TWO +ve leads and TWO -ve leads - thus there are six wires, which will now go up to the opening on the underside of the wing and into the servo bays where they will be soldered onto the previous cut wires, and sleeved with heat shrink. By carefully arranging the length of the wiring you will be able to plug and unplug the wing AND separate the two wing halves, folding them together for transportation, while maintaining servo connection.
Review by: Bryan Windus-SmithBaster 2e
Very pleased with my Blaster 2e, it has opened me to a side of the hobby I had previously ignored.
I have enjoyed power flight and slope soaring for 30 years, and the Blaster 2e is my first moulded DLG / Thermal Soarer. The build was challenging, but satisfying, and all the build challenges melted away on the first flight - this is one incredible machine!
Having an all-moving tailplane, I did several un-powered glide tests to make sure it did not nose into the ground. By the third throw it glided flat for over 50 metres! The flaps have a massive effect and when fully deployed, the Blaster flies backwards in a 9mph breeze, yet remains completely under control. Some mix is needed with throttle and elevator as it wants to climb with power applied, but nothing serious.
It will find lift off almost anything or anyone: fence, tree-line, buildings, children, slight bump in the ground, etc. etc. There is a strange inner joy in finding lift like this, so much so, that I am now totally hooked on flat field soaring.
Service and help from Hyperflight has been without fault.
Would I recommend Hyperflight and the Blaster 2e? - Absolutely!
Dymond D47's all round
EMAX CF2822 Outrunner
DualSky 30 amp speed controller
LoongMax 500mAh 20C to 30C flight battery
8 x 4 CAM Carbon folding propeller with RFM CFK carbon spinner
Jeti Duplex 2.4EX R6 Rx with MUI 30 telemetry module
Motor / propeller combination gives 90 watts, which is enough to climb vertically out of sight.
All-up weight, with weight in the tail to balance: 14oz.
Review by: John Fisher
Very pleased with the Blaster.
Flies amazingly well. I am very impressed.
All up weight is 478 gm.
Hacker A20 22L motor with X30 Controller and 9 x 5 Aeronaut folder
HYPERION G3 CX-25C 0850-3CELL LIPO.
Just need to buy 2.4 Radio to save some weight?
Review by: John Fisher
Blaster arrived today less than 48 hours after order placed - amazingly quick.
Kit looks amazing too!
Review by: AndrewTReport Back
I thought I'd report back on my two Blasters.
The e version is my most used and favourite model. It is fantastic to
fly, flies for 30 mins upwards on a 700 mah lipo and copes with quite
strong winds. The only thing it won't do is knife edge! I will have to
consider getting a spare in due course.
The dlg version is terrific - I can now get 5 mins upwards flights in
decent sunshine on the smallish playing fields at the bottom of my
garden. I have discovered that the secret to a high launch for me is to
be very relaxed and to extend my left arm with the transmitter as a
counter-weight. I have no idea how high I am getting - I would guess
about 100 feet at best. What should I be aiming at? I flew it at
Ivinghoe Beacon last Sunday in 15 knots of wind and it was superb. I
will need to get a lost model alarm as I messed up one landing behind
the hill and lost it behind a hawthorn tree.
Review by: JordiOutstanding Quality
I've been watching carefully my new "toy", and the word that comes to my mind is outstanding. I've been modelling for 35 years and I never found such high quality in a model. I also have a Stuart Blanchard's Calypso Sport and F3B New Age, they fly very well indeed, but they haven't the same manufacture quality.
I heard about Vladimir's building quality, but the only one model I saw some years ago was a Graphite. It looked very nice, but the Blaster overpassed it.
I'll be building it up next week (if work allows me to do so). I'll give you my comments soon.
The Blaster got airborne today. It's a delightful to fly. It's very agile, tight thermal turns are possible without loosing any height.
I found the CG too forward without posibility to move any item backwards, I'm using 2S 800 mA Lipo (45g). This give me about 1 hour flight. I'm thinking about replacing the battery, 30g, perhaps, but I'm not sure. From your point of view, can you suggest any Lipo combination to achieve the right Blaster CG?
Pass my congratulations to Vladimir for this great design. Kind regards,
(I suggest using light weight powertrains and 400-500mah 2S lipos, even if using lightweight tail servos - Neil.)
Review by: JohnHBlaster 2e & Supra
I just thought I would let you know how much I am impressed with the Blaster Electric, this week is the first opportunity I have had enough time to do it justice.
I am more than impressed with its performance, it exceeds all of my expectations, I have just come back from a session with just two powered launches with both flights having to spiral out of exessive lift with flight times of 45 and 38 minutes, the plane was as high as I could see effectively.
Last week I had the Blaster (non electric) out and recorded a flight time of 36 minutes again having to spiral out of lift. Lovely machines both.
I was also flying the Supra E on Sunday and got to a height of 290 Metres logged by the Alti Pro from Martin Bell from a launch height of 200 metres.
I am so impressed with the developments in the sport in the last couple of years, my flying buddies at my flying club thought I was mad about 5/6 years ago when I decided to ditch all of my I/C in favour of electric power, guess what most of them are flying now!
Again many thanks for introducing me to Vladimir's models
All the best