BAMF2 1.5m DLG

We are pleased to now be stocking the BAMF2, the acclaimed 1.5m DLG originally only available from Armsoar. From their experience flying the BAMF they saw that higher heights and higher penetration were always required to keep pushing forward. They saw that competition is biasing towards planes that penetrate very strongly with less disturbance from turbulence, so they developed he BAMF2 with those goals in mind.Aerodynamically, the wing shape was modified to be less affected by turbulence while the lift is slightly increased closer to the root. All cross-sections on the fuselage are decreased and the pushrod exits are further refined for a tighter install. In terms of flying philosophy, we feel there are two ways to tackle high winds: fly extremely fast with a lower L/D so you can reach somewhere faster, so even though L/D is lower you will reach the target area quicker and less affected by the outside forces (wind & turbulence), or secondly slightly slower than extreme but retain very high L/D so even though it may take you a few seconds to get back you should get back with a little extra height.Mechanically, Armsoar wanted/needed a model that can really break down small. As such, the BAMF 2 comes with a center split 2-piece wing with a fat carbon joiner, with the option of a very simple removable fin that will be strong enough for *most* pilots. For extremely powerful launchers, it's probably still safer to glue the fin on. The nose is extended to reduce the need for nose weight and to make gear selection, install and maintenance extremely easy.The BAMF 2 is made in Ukraine. All models are made with solid Cascell cores, carbon shear webs, and high-quality finish. Images shown are a representation of the model only and may differ slightly due to the handmade nature of the model.See this RCGroups BAMF2 thread for a lot more info.For build info see Armsoar BAMF2 Assembly Instructions.Structure:

• Solid Cascell moulded wing and tails
• Light: CW30 skin
• Standard: CW40 skin
• Strong: Co-axial CW60 skin
• Tails: CW20 skin
• 1-piece fuselage
• 2-piece wing (centre split)
• Nosecone
• Right-handed launch (please message us for left-handed version)
• Removable wing
• Removable horizontal tail
• Removable vertical tail (optional during build)

Flight Characteristics:

• Incredibly high launching
• Cuts through wind and turbulence at low weight

Specifications:
Wingspan: 1495 mm
Wing area: 18.55 dm²
Wing airfoil: modified Synergy 2
Light AUW: ~205-210 grams
Standard AUW: ~215-220 grams
Strong AUW: ~225-230 grams
CG: 64.0 mm (active air) to 69mm (calm)Recommended Gear:
Receiver: FrSky GR6, FrSky R6, Spektrum AR410, AR6610T, Futaba R3004SB
Servos: 4* KST A08N v6, 4* X08N v6
Battery: 1S LiPo 350 mAh to 500 mAhIncludes:
Left wing panel
Right wing panel
Fuselage
Nosecone
Horizontal tail
Vertical tail
Wing joiner
Pull-string wire
Crimp tubes for pull-string
Springs for tail
ArmSoar 3D throwing blade (light)
Tail screws
Wing screws
Wing control horns
Elevator control horns
Rudder control horn
Wing pushrod wires
Wing pushrod sleevesCamber:
Launch preset: 2mm up
Zoom: 2mm up
Speed: 0.5mm down
Cruise: 3mm down
Float: 7mm downAileron Throw:
Speed: 6mm up, 8mm down
Cruise: 6mm up, 13 mm down
Thermal: 5 mm up, 18mm downElevator Throw:
Speed: 6mm up, 8mm down
Cruise: 10mm up, 10mm down
Thermal: 11mm up, 11mm downSnap flaps (elevator to camber mixing):
1.5mm with full elevator deflectionAileron-Rudder mix:
5mm rudder with full aileron deflection