Electronics ‐ Other RC Electronics
The AerobTec Altis v4 is a multi purpose device: The AerobTec Altis v4 is an RC altimeter designed especially for F5J and eSoaring electric glider competitions, though it can also be used to record the barometric altitude of any object - a RC model, a bird, kite, or full size aircraft. Its unique benefit is the built-in screen that displays the F5J Start Height (or other data) automatically. This allows F5J competitions to be run very easily and safely, with no plugging in of gizmos or fiddli...
NEW AerobTec Altis v4 F5J Start Height Recorder and Flight Logger
A Altis V4 Telemetry Cable for connecting Jeti Duplex and Multiplex M-Link 2.4GHz receivers to an Altis V4. This cable allows the Altis V4 to act as a sensor for the receiver, so the data values can be displayed on the transmitter screen (or annunciated) during flight.
NEW Altis V4 Telemetry Cable
A high quality Micro B USB Cable. This 1.8m long cable has a standard full sze USB plug at one end and the new Micro B USB plug at the other. It is used for the Atlis V4 logger and for connecting Android phones to a PC.
NEW Micro B USB Cable for Altis
Now supplied with a USB interface The high accuracy RAM3 Recording Altimeter for Models flight logger holds up to 65000 altitude readings in its ample RAM capacity, yet is smaller and lighter than competing devices. The Recording Altimter for Models (RAM3) records altitude and displays it on your PC. The RAM3 has a resolution better than 1ft, aided by reading every sample thousands of times. The RAM3 holds up to 18 hours of data when sampling at 1 sample per second. It has a tiny postage stam...
RAM3 Recording Altimeter for Models
70 mAh LiPo battery fitted with a RAM3 plug. Also supplied with a matching socket that can be use to make up a charge lead. Charge the 1S LiPo battery at 70mA.
RAM3 70 mAh LiPo & lead
Out of stockMore Details
Custom lead to connect the RAM3 to a PC using the ubiquitous USB interface. This product can be used with older RAM3 altimeters (that were supplied with RS232 cables) to convert them to the USB standard. Note the USB interface is built into this special lead, this is not an off-the-shelf cable. Installation Instructons There are two steps to install the USB upload cable. First, the proper software drivers must be available so that your computer can recognize and install the cable when it&rsqu...
RAM3 USB Interface and Lead
Replacement plug and lead for the RAM3 altimeter. Also supplied with a matching socket that can be use to make up a charge lead.
RAM3 Plug & Lead
Competition Altimeter for Models Designed by Soaring Circuits for the US 200m altitude limited electric soaring format, the CAM is small, light, and easy to install. Just plug it in between your receiver and ESC. That's it! The CAM automatically shuts your motor down at 200 meters or after 30 seconds per the emerging altitude limited soaring rules. This simple competition format promises to put the "soaring" back into electric sailplane contests. Even inexpensive RTF models can compete! T...
CAM Height Limiter
Mini JST Socket with an 11cm long lead for use with our small LiPo batteries. Also called female red BEC connector.
Mini JST (BEC) Socket with Lead
Mini JST Plug with an 11cm long lead for use with our small LiPo batteries. Also called a male red BEC R/C connector.
Mini JST (BEC) Plug with Lead
Functions: Count Down Timer, Stopwatch & Clock. Voice on/off switch Various noises at zero can be selected when counting down Has a mounting clip on rear suitable for Tx handle. Size: 83 x 65 x 10 mm exc. Clip Count Down Timer announces at every hour down to 1 hour, then every minute down to 1 minute, then 50, 40, 30, 20, 10 seconds & then counts down 9, 8, etc to Zero and announces ‘Times Up’. Carries on counting & and announces at each minute of over-run time. Stopwatch does not ...