Electronics ‐ Altimeters, AMRT & Altitude Switches
The AerobTec Altis V4+ is a great multipurpose device suitable for F5J, eSoaring, DLG, and all pilots wanting altitude. This updated Plus version contains an improved precision altitude sensor with lower noise, and the display has been updated to a higher contrast version with a white background. The AerobTec Altis V4+ provides these facilities: The AerobTec Altis V4+ is an RC altimeter designed especially for F5J and eSoaring electric glider competitions, though it can also be used to reco...
AerobTec Altis V4+ F5J Start Height Recorder and Flight Logger
The Aerobtec Altis Micro is functionally very similar to Altis v4, except that is does not have a display. The main benefits are smaller dimensions and lighter weight, making it suitable for smaller eSoarers and discus launched gliders. The AerobTec Altis Micro is a multipurpose device: The AerobTec Altis Micro is an RC altimeter suitable for discus launch gliders and F5J and eSoaring electric glider competitions, though it can also be used to record the barometric altitude of any object - a R...
The new Aerobtec Altis GPS logs GPS coordinates, ground speed, barometric pressure altitude, and RC input, allowing the 3D position and speed of a model to later be displayed on a computer. As the barometric pressure altitude is much more accurate than GPS height info this device is much better than most loggers for model aircraft use. It also has support for Jeti, Multiplex, Graupner, Futaba SBUS2* and FrSky S.Port* telemetry, allowing the RC pilot to receive real-time data via his transmitter...
The Aerobtec Altis Device Terminal is can be used as a display for the new Altis Micro. It also works as a battery tester, a PWM display and tester (to check out receivers) and a servo tester. It both generates and measures PWM servo pulse trains.
Aerobtec Altis Terminal
The Altis AerobTec V4 Keypad allows the Altis V4 to be setup on the field when loaded with the standard firmware. The keypad allows you to make changes to the motor run time, height cut off, motor restart, competition restart and F5J setting. When using the logger the Altis v4 has to have its port A set to Keypad, so the keypad cannot be used at the same time as the telemetry facility. To enable the keypad you may need to upgrade both the computer software and the Altis V4 firmware to the late...
Altis V4 Keypad
The Altis AerobTec Telemetry Converter is an interface for Futaba and FrSky users. It interfaces the Altis V4 or Altis V4+ to the telemetry port of Futaba and FrSky receivers, so the pilot can see/hear the height etc info on the ground, via his telemetry equipped tx/rx 2.4GHz link. Comes with standard RC input and output leads, and an RC to Molex convertor lead.
Altis Telemetry Convertor - for Futaba & FrSky
The Altis AerobTec Telemetry Converter HS is an interface for users of Spektrum and Hitec RC gear. It interfaces the Altis V4 or Altis V4+ to the Telemetry port of Spektrum and Hitec equipment, so the pilot can see/hear the height etc info on the ground, via his telemetry equipped tx/rx 2.4GHz link. Comes with standard RC input and output leads, and an RC to receiver convertor lead. When using Spektrum gear a Spektrum TM1000 module is also required.
Altis Telemetry Convertor - for Hitec & Spektrum
A Altis aerobTec Telemetry Cable for connecting Jeti Duplex and Multiplex M-Link 2.4GHz receivers to an Altis V4. This cable allows the Altis V4 to act as a sensor for the receiver, so the data values can be displayed on the transmitter screen (or annunciated) during flight.
Altis Telemetry Cable
A high quality AerobTec Micro B USB Cable. This 1.8m long cable has a standard full size USB plug at one end and the new Micro B USB plug at the other. It is used for the Altis V4 logger and for connecting Android phones to a PC.
Micro B USB Cable for Altis
Now supplied with a USB interface The high accuracy RAM3 Recording Altimeter for Models flight logger holds up to 65000 altitude readings in its ample RAM capacity, yet is smaller and lighter than competing devices. The Recording Altimeter for Models (RAM3) records altitude and displays it on your PC. The RAM3 has a resolution better than 1ft, aided by reading every sample thousands of times. The RAM3 holds up to 18 hours of data when sampling at 1 sample per second. It has a tiny postage sta...
RAM3 Recording Altimeter for Models
Custom lead to connect the RAM3 to a PC using the ubiquitous USB interface. This product can be used with older RAM3 altimeters (that were supplied with RS232 cables) to convert them to the USB standard. Note the USB interface is built into this special lead, this is not an off-the-shelf cable. Installation Instructions There are two steps to install the USB upload cable. First, the proper software drivers must be available so that your computer can recognize and install the cable when it&rsq...
RAM3 USB Interface and Lead
Designed solely for F5J competitions, the CAM F5J is the easiest to use F5J altimeter. No programming is required. No computer is needed. Just plug it in and fly! When you land read the F5J Start Altitude on the clear OLED display. It couldn't be easier. Plug in - fly - readout - win! The CAMf5j is already approved by the FAI for international F5J competition.
Competition Altimeter for Models Designed by Soaring Circuits for the US 200m altitude limited electric soaring format, the CAM is small, light, and easy to install. Just plug it in between your receiver and ESC. That's it! The CAM automatically shuts your motor down at 200 meters or after 30 seconds per the emerging altitude limited soaring rules. This simple competition format promises to put the "soaring" back into electric sailplane contests. Even inexpensive RTF models can compete! T...