Prices shown exclude VAT 

Smile F3K 1.5m DLG

Product Code: SMILE2
 (1 review)

Price: $584.64

More than 10 in stock
Add to basket to see shipping cost

Available Options

* Wing colour (serial #):
* Wing & Tail Bags:
Quantity

Description

Black Friday Deal

The Smile F3K is a great discus launched glider from AJ Aeromodels. Like the Snipe it has very high aspect ratio wing, giving it a high launch and a great glide angle. The design shows a strong Snipe influence, employing similar pylon mounted tailplane. Like the Snipe the model flies very well, with high launches and a good speed range.

The wing and tail are beautifully molded from ultra-light spread carbon over a Rohacell 31 foam core. This makes the wing light, accurate, and comparatively tough and repairable if necessary. The lightweight tailplane (horizontal stabiliser) is mounted on a molded carbon pylon, which can be mounted above or below the boom, to the modeller's preference. The fuselage is a very rigid spread carbon molding, with a good sized canopy hatch, aiding the RC installation. The tailboom has an oval cross section to increase stiffness and improve the launch height.

The model is supplied with horns, pushrods, pull cable, torque springs, servo mounting plate and a very nice offset throwing blade. The wings are supplied in thin foam bags but fit nicely in our DLG F3K Wing Bags and the tails in our DLG F3K Tail Bags for greater protection. No build manual is available but there is some useful info in this RCGroups Smile thread, and some construction photos on Facebook here.

Although the completeness of the kit and the quality of construction and detail design is excellent there are a few small paint and surface finish blemishes, hence the reduced price. But do not let that put you off, these are still beautiful models and a fantastic bargain.


Smile DLG Specifications
Wing span 1.5 m 59 in
Wing area 19.2 dm2 298 sq in
Length 112 cm 44.1 in
Flying weight from 235 g 8.3 oz
Wing loading 12.3 g/dm 4.0 oz/sq ft
Aspect ratio 11.6
Wing airfoil Proprietary
Dihedral angle 5.5º
Centre of Gravity 73-78 mm from wing leading edge
Controls Rudder, elevator, ailerons


Smile DLG Typical Weights
Fuselage 32.0 g 1.1 oz
Wings 109.0 g 3.8 oz
Fin 6.6 g 0.2 oz
Tailplane 7.2 g 0.3 oz
Accessories 16.5 g 0.6 oz
Total structure 171.3 g 6.0 oz
Glue etc 5.0 g 0.2 oz
Receiver 5.0 g 0.2 oz
Tail servos 16.0 g 0.6 oz
Wing servos 16.0 g 0.6 oz
Battery 22.0 g 0.8 oz
Flying weight from 235.3 g 8.3 oz

Note the weights above are not 100% accurate - the current batch of models weigh more.

Smile Control Throws & Mixes
Rudder 15 mm each way
Elevator 7 mm up / 7 mm down
Ailerons 10 mm up / 8 mm down
Recommended snap-flap (elevator->camber) mix.
Full up elevator gives 5mm increased flaperon camber
Recommended flaperon settings. Down=Flap TE down.
Launch preset 1 mm down
Speed 1 mm up (small ail>rud mix)
Cruise 0 mm (a little more ail>rud mix)
Slow cruise and active thermal 1 mm down (more ail>rud mix)
Minimum sink 3 mm to 4 mm down (Slow cruise + slider camber)
Landing mode as much down as possible


Recommended RC
All servos KST X06N, KST X08N, MKS DS65K, MKS DS75K-N, MKS HV75K-N, MKS DS6100, MKS HV6100, Blue Bird BMS-126WV
Receiver 4/5 channel rx to match your transmitter, eg FrSky X4R, Spectrum AR6610T, Lemon LM0034, Futaba 6008HS*, Futaba R6106HFC *case removed
Power 1S 500-700 mAh, Radient 1S 700 mAh, HyperLiPo 2S 300 mAh LiPo

Reviews 1  


 Review by:

This is my first cabin dlg ,Good glider , nice carbon for the price. Went together well , I would say would benefit from a servo tray to make the job easier and taking a lot of the guess work out. Havenít flown yet but will be getting out for madian flight soon.
Package very well and delivered very quickly good job hyper flight.


Related Categories

Related Products 0

Shop Securely

Follow Us

facebook   facebook   twitter   Google My Business

Contact Us

HyperFlight
Drybank Farm
Fosse Way, Ettington
Stratford-upon-Avon
Warwickshire, CV37 7PD
United Kingdom
+44 (0) 1789 336166
sales@hyperflight.co.uk
Contact Form