|Kappa 40 Specifications|
|Wing span||3.9 m||155 in|
|Wing area||68.7 dm2||1065 sq in|
|Length inc spinner||161 cm||63.4 in|
|Flying weight from||1315 g||46.4 oz|
|Wing loading||19.1 g/dm||6.3 oz/sq ft|
|Spinner Diameter||38 mm|
|Centre of Gravity||85-90 mm from wing leading edge|
|Controls||Rudder, elevator, ailerons, flap, throttle|
|Kappa 40 Light Layup Typical Weights|
|Fuselage & pushrods||160 g||5.6 oz|
|Wing centre panel (Light)||336 g||11.9 oz|
|Wing tips (Light)||374 g||13.2 oz|
|Tail plane||44 g||1.6 oz|
|Fin||31 g||1.1 oz|
|Accessories & glue||12 g||0.4 oz|
|Total structure||957 g||33.8 oz|
|Wiring||30 g||1.1 oz|
|Receiver||8 g||0.3 oz|
|Rudder servo||10 g||0.4 oz|
|Elevator servo||10 g||0.4 oz|
|Wing servos (4)||40 g||1.4 oz|
|Speed control||35 g||1.2 oz|
|Motor||120 g||4.2 oz|
|Prop & spinner||25 g||0.9 oz|
|Battery||80 g||2.8 oz|
|Flying weight||1315 g||46.4 oz|
|Elevator & rudder||MKS DS6100, MKS HV6100, KST X08, Blue Bird BMS-A10H, Blue Bird BMS-106HV, Blue Bird BMS-107HV|
|Aileron||MKS DS6100, MKS HV6100, MKS HV6110, KST X08, Blue Bird BMS-A10V, Blue Bird BMS-105HV, Blue Bird BMS-106HV|
|Flap||MKS DS6100, MKS HV6100, MKS HV6110, MKS HBL6625 Mini, KST DS135MG, KST X10 Mini, Blue Bird BMS-105HV|
|Kappa 40 Control Movements|
|Rudder||20 mm each way|
|Flap||85 degrees down|
|Ailerons||15 mm up, 12 mm down|
|Elevator||10 mm up, 10 mm down|
|Recommended camber settings (measured at flap root TE)>|
|Speed mode||-1.5° (flat bottom surface)|
|Cruise mode||0° (flat top surface at hinge)|
|Thermal mode||+2° (2 mm down)|
|Kappa 40 Powertrain Recommendations|
|Powerline Micro 1025/F5J||3S 1.3Ah LiPo, 16x8 RF or GM prop (2000 fpm, 43A)|
|Leomotion L3007-5000||3S 1.3Ah LiPo, 14x8 prop (1750 fpm, 39A)|
|Leomotion L3013-4550||3S 1.3Ah LiPo, 15x9 prop (2250 fpm, 57A)|
|Hacker A20-6XL geared 4.4:1||3S 1.3Ah LiPo, 16x9 Aeronaut prop (1950 fpm, 46A)|
|Mega 16/25/4E direct drive||3S 1.3Ah LiPo, 12x6 prop ( 1800 fpm, 59A)|
|Mega 16/5/3||Maxon 4.4:1 gearbox, 3S 1.0Ah LiPo, 12x6 prop|
Review by: CJSKappa 40, (D box), 'the Big K'
Been having a hard time this year in deciding where to go E-glider wise . . . thin wing sections, super light, radical design. All have 'buy me' stamped all over them, a lot of thought, watching and discusion finaly bought me to Kappa. I had a 35 for a few months about 3 years back, inexperiance bought that association to an early, abrupt and dramatic end.
However, I have never forgoten what an impresion the Kappa 35 made on me and my flying friends. Reasoning, 'better a devil you know . . . ' the big 'K' ticking all my boxes, in due course a large box was delivered.
Unpacked, inspected, all OK as has always been with goods ordered from Hyperfligth. A couple of weeks pawing over Kappa 40 got me fully familier with the way I was going to assemble it. Tail, wings etc., all went together nicely, the Blue Bird 105 wing servos were mounted in cradles with an extra head bearing. Needed a little bit of redesign of the servo bays removing the ply push rod keepers which were re instaled in the servo cradle.
Rudder and elevator servos were instaled in a conventional upright tray at the back of the cockpit, a tray is suplied but I prefered the old fashioned way.
Now we come to the nose and motor instalation. Originaly, I was to fit a Glider Drive 960, a tad heavy although a dry run earlier in the assembly had indicated it would ballance out OK. It was the 38mm can diamiter that put me off. So I chose a SK3 28-36. I used a motor mouting system that is a one off to me, keeping the ESC fixed in the top of the fusalarge, wires away from the out drive motor can. The 1800mah 3s battery sliding in under neath up to the motor with a gap keeper, no crumpled wires in a heap.
The 28-36 motor produces a little over 300 watts from an 11x6 carbon toothpick style blade. The building was streight forward enough provided a little experiance is used?
(as an aside, I have also produced a power train using the Glider Drive. Not flown it yet but worked out a way to get a quart into a pint pot, thats 38mm through a 27mm opening)!
So we come to the 'nity grity', how does 'the Big K' perform . . . . .
It has had about one dozen flights so far, flew from the maiden launch with no problems, it flies. I have needed that dozen flights to get things the way I like them, but the throughbread that she is came through exhibiting good charicturistics that could be built on in the trimming process.
Today I deliberatly went for a session with a forcast 14mph wind . . . How did she handle herself, thats just the point, she flew as though it was her normal weather. The 14mph wind was much more like 20mph we estimated at 200m, making no bones about the buffeting she was getting, a friend comented on how similar she flew compared to a DLG,. Take the rough with the smooth, but do nothing that would alarm the pilot. Penetration was easily controled with camber mix and speed mode, along with a little encouragement from the pilot.
So there you have it, Kappa 40 the 'Big K', 1450grs (mine is the carbon 'D' box ley up) of high aspect ratio sailplane, that seems to want to 'fly'. She leaves me wanting to get bak to the field asap to explore more posibilities and refine those that curently show. It also means I will be a better pilot in due course with the 'Big K' as my teacher.
Nearly forgot, the flaps, landing today was not easy, being a bit bumpy in the last 20m or so. Kappa excelled in her stability, responding gently but positivly to every input. Those watching were waiting for here to drop a wing, she simply glides in giving me no cause for consern, as I say, responding smoothly to every input. These landing realy did end every flight with a smile on my face and some very impressed spectators.
Well worth the 5+ stars IMHO
Review by: Michael ConnellKappa 40 F5J Spread Carbon
Review of Kappa 40 F5J Spread Carbon.
I decided to spend some cash on a new F5J glider. This is based on the fact you cannot take it with you when you go. Only the best will do and no expense spared. I regularly compete in the Bartletts league and F5J. The first question is what to buy? We are spoilt for choice with all the models available. I had not seen a Kappa 40 in the flesh but it looked good to me when Skip Miller was testing a Kappa 35 on U Tube. I was sold.
I thought that looks competitive and it’s different. The flying weight was quoted 1315 grams and it look state of art and modern. I am not technical enough to discuss the merits of high aspect wings etc. The advertising says it banks in a very tight circle and it does. The first flight was 10 minutes plus in not very good conditions. I suspect in competition that will change.
I bought the most expensive model from Hyperflight and that was spread carbon model which came in a red/orange livery. It looks very attractive to me. The electric motor is a Leomotion 3007-5000 F5J 6.7:1, YGE 60 Esc, Elevator, Rudder, Ailerons, MKS DS 6100, and Flaps, KTS DS125MG. RX Futaba R617FS. All items new. Total cost £2,500.00 plus or minus a few pounds.
The model came in a large box and well packed. There are no assembly instructions. The standard or manufacture is very good in my opinion.
You need some experience to assemble this model and other models I would suggest. There was a bag of profiled ply bits which I could not fathom. I contacted Neil who came back with a drawing. The drawing showed how to assemble the bits to hold the elevator and rudder servos. I did not like the design so I installed my own design. I then had to install the pushrods for the elevator and rudder. I used some magnets which held the pushrod in place and then ran some cyno down the fuse. The finished installation is a very firm with no slop at all. In my opinion the elevator is the most important servo on the glider.
The next operation was install the motor. The fuse comes with the firewall already installed. The Leomotion motor has a stepped front. You cannot fix directly to the firewall. So I cut a 4mm Circle of plywood and placed over the step. The circle was pre-drilled and stuck to the motor. I then attached the ESC and tested before installing. The fuse nose is very long. To attach the motor I used 2.5mm threaded rod and pulled the assembly into place and then fixed with the motor screws. I ensured there was a good flow of air through the firewall. The next job was to fit the servos in the wings. The wings come with pre-cut holes for the electric connectors. A little bit of filing was needed but it all went together without a problem. The aileron and flap horns are fitted and include the servo control rod. I used wood mounting frames which are glued to the wing with cyno or epoxy. The aileron servos are hot glued in place and the flap servos fixed with screws. It all went together with little fuss. I made the wiring harness and used a multiplex connector for connection to the wing. The wing fits directly on the fuse and then held with 2 bolts. I bought some very expensive Vitoprop but they did not sit against the fuse. Neil would not accept them back as he said they had been used, which they had not. Anyone, going cheap. The CG was back too much. I was going to use a 1300 x 3 x 30C battery but the glider was too light at the front. I had a 2200 x 3 x 30C battery and that was perfect. The CG is spot on. I am about 100 grams over the published flying weight but there is nothing I can do about that. The watt meter showed 37 amps 360, watts which is more than enough. 248 watts a kilo. I could have got away with a 40 amp ESC but the 60 amp will not get stressed. I did many calculations on E-Calc, and it was correct.
I have been advised it Kappa 40 will fly up to 15 – 20 mph. There is no method of ballasting it, but I am working on that.
My opinion so far is that I am pleased and think it has good potential. I look forward to seeing you on the flying filed.